Customer Support - (813) 235-0800 Call Us Text A VIN#
Mon-Thu 9AM-8PM  |  Fri-Sat 9AM-5PM EST

Transmission CV Joint Symptoms

What is a CV-Axle/Joint?

  • SYMPTOMS of a Bad CV Joint
  • CV Boot Replacement and Cost

Get A Transmission Quote


What Is a CV Axle?

CV (constant-velocity) axles, (also known as half-shafts), are used in front-wheel drive vehicles to transfer the engine’s power from the transaxle to the two drive wheels.  Some late model vehicles with independent rear suspension and some four-wheel and all-wheel drive vehicles also use CV axles.

A CV axle has two CV joints (an inner joint and an outer joint).  These joints allow the axle to transfer the engine’s power to the drive wheels at a constant speed while accommodating for the different travel conditions, including the up and down motion of the suspension and cornering.  Without constant-velocity joints, the axles would bind or break whenever the vehicle hit a bump in the road or turned a corner.

CV joints are packed with grease for lubrication.  To keep the grease in the joint and moisture, dirt and roadway grime out, the joint is covered with a rubber boot called a CV boot.  CV boots are made of a durable rubber that can withstand extreme weather and travel conditions.  Good quality CV boots can easily last 100,000 miles or more.  But, because they are constantly exposed to the elements, a CV joint boot can be damaged at any time.  For this reason, it is a good idea to routinely inspect your CV boots for damage.   If your vehicle has more than 125,000 miles – it is a good idea to check the CV joints more often.


How CV Axles Fail

Actually, CV axles rarely fail – it’s the CV joint(s) that fail and they typically only fail because of a damaged or torn CV boot.  When a CV boot fails due to age and wear, or is damaged by roadway debris, the grease that keeps the joint lubricated quickly leaks out of the joint and dirt, roadway grime and moisture enters the joint. When this occurs, the CV joint will soon fail.

Of the two joints, the outer CV joint almost always fails first because it does more work than the inner joint so it wears out sooner.  The outer joint is also much more likely to be damaged from roadway debris because of its location.  For these reason, if you suspect CV-joint failure, odds are it is the outer joint that has failed.  (See above image)

NOTE: While a damaged or torn CV boot is almost always to blame for a failed CV joint, like any part, CV joints can wear out over time.  As the joint ages and wears,  tight tolerances give way to added space opening up between the moving parts of the joint.  As space between the parts increases the parts begin to bang against each other and after awhile they break.


Symptoms of a Bad or Failing CV Joint

A bad or failing CV joint will oftentimes make a clicking, popping or grinding noise, especially when turning.  At low speed, a bad CV joint may make a steady knocking sound every couple of seconds or so.  A bad CV joint can also cause a vibration that is felt in the steering wheel and floorboard of the vehicle – this may happen only at certain speeds.

INSPECTING a CV Axle and Checking/Testing a CV Axle

A routine inspection of the CV axles and CV boots and checking/testing a CV axle you suspect of being bad are two different processes.   Below is an explanation.

Routine CV Axle Inspection

Inspecting a CV axle involves a visual check of the CV boots.  In most instances, all you will need is a flashlight.

Follow these Steps…

Inspecting a CV axle involves a visual check of the CV boots.  In most instances, all you will need is a flashlight.

Follow these Steps…

  Park the vehicle on level ground and set the emergency brake.   If necessary, lift the front of the vehicle and secure with jack stands.  
  With your flashlight in hand, slide underneath the vehicle.  If you’ve raised the front of the vehicle, you can slide underneath at the front center, which will enable you to see and inspect both CV axles.  Or, when there is less room underneath the vehicle to maneuver, slide underneath one side of the vehicle immediately in front of or behind the front wheel to inspect one axle at a time.  

Inspect the CV Joint Boots.    When you are in a position to see one or both CV axles, look closely at the CV boots located at each end of the axle. (Each axle has two CV boots).  Visually inspect each rubber boot for cracks and tears.  Also check for a damaged or missing boot clamp.  For any areas of the boot you cannot see, use you finger to feel for the presence of grease.  A damaged boot will expel grease onto the outside of the boot and surrounding area.

The axle passes the inspection if no visual crack or tear is seen or felt in either boot and there is no presence of grease on the outside of either boot.


Checking/Testing a CV Axle You Suspect of Being Bad

Checking and testing a CV axle you suspect of being bad or beginning to fail involves a visual inspection, a movement test and a drive test. 

Follow these Steps…

  Follow the steps above to inspect the CV axle and CV boot for damage.
If one of your CV axles is showing symptoms of being bad or going bad, you will probably see a damaged or torn CV boot when you do the above inspection.  However, regardless of what you find during the inspection of the CV boots, if you still suspect you have a bad CV axle/joint, you will need to do a feel and drive test to confirm.
  Allow engine to cool.  From underneath the front of the vehicle, grab the CV axle with a firm grip and attempt to move sideways and then in and out.  The CV axle should have very minimal movement in any direction.  If you are able to move the axle more than 1/8 inch in any direction, it is probably time to replace the axle.  

Take the vehicle for a drive.  To get an accurate reading of the CV axle condition, find a smooth flat surface (such as an empty parking lot) and turn the steering wheel all the way in one direction and drive in a circle.  Then turn the steering wheel in the opposite direction and drive in a circle.  If one of the CV joints is bad, you will hear a popping or banging noise as you travel in a circle.

WARNING: If you hear a CV axle popping or clicking when traveling straight, the CV joint is near the end of its service life and will completely fail soon.  At this stage the CV axle must be replaced soon.




CV Boot Replacement

1. How to Determine the Condition of a CV Joint
2. The 3 Types of Replacement CV Boots
3. CV Boot Replacement Cost

BEFORE replacing a CV boot, you must first determine the condition of the CV joint.

When the grease is expelled out of a CV joint due to a damaged or torn CV boot, the joint will begin to wear much faster and will soon fail.  Once the CV joint is damaged, packing the joint with new grease and installing a new CV boot will not repair the already damaged CV joint.  The only remedy for a damaged CV joint is replacing the CV axle.  So, before repacking a CV joint with new grease and installing a new CV boot, you must first determine the condition of the CV joint.

How to Determine the Condition of a CV Joint
1. Using a bright flashlight, look inside the damaged or torn CV boot. Look closely at the CV joint – is there still some grease in the joint?

2. Firmly grasp the CV axle near the joint and attempt to move the axle back and forth and then in and out.  There should be little or no movement in any direction.

3. Drive the vehicle to an empty parking lot or any open space where you can drive in a circle without endangering yourself or others.  When safe to do so, turn the steering wheel all the way in one direction and driving in a circle.  Now, do the same thing in the opposite direction.  Did you hear a clicking or popping noise when traveling in a circle in either direction?

Conclusion: If there is still some grease in the CV joint, if you felt little to no movement when attempting to move the axle by hand and if there was no clicking or popping noise when driving in a circle in either direction then the CV joint is good.  Replacing the damaged CV boot may be the appropriate repair.

NOTE: A CV joint that is dry (no grease) but passed the movement test and driving test is also good.  However, the window of opportunity for packing the CV joint with new grease and replacing the CV boot is short.  With no grease in the joint, joint failure will occur very quickly.

Types of CV Replacement Boots

There are basically three types of replacement CV boots.  These are explained as follows:

The first type is a conventional CV boot design, which requires the CV axle to be removed from the vehicle and then the CV joint to be removed from the axle before packing the joint with grease and installing the CV boot.  This is the best of the three CV boots but is also the most costly (or time consuming) to install.

The second type is a “stretch boot” design, which does not require the removal of the CV axle to install, but does require the removal of the wheel and wheel hub assembly.  With this design, the CV boot is stretched over the CV joint and is held together using a special glue or large clamps.  Because the stretch boot is a one piece boot, it may last longer than a split type boot but the downside is that installation is not as easy as the split boot design.

The third replacement CV boot is a “splitboot” design.  Being split, this CV boot is installed by simply opening up the boot at the split and placing it over and around the CV joint. The boot uses a special glue or large clamps to seal the boot tightly around the CV joint. The split-boot design is installed without removing the wheel, hub or any other parts. Of the three boot designs, the “split-boot” is considered the weakest but is clearly the easiest and least costly boot to install.  

CV Boot Replacement Cost

Auto repair shops and car dealership service centers do not typically replace CV boots – they will insist on installing a new CV axle whenever a CV boot and/or CV joint has failed.  The reason is that the labor cost for replacing a CV boot is more than the cost for replacing a CV axle.  The CV boot kit costs less than a CV axle but the difference is less than the labor difference.  The example below illustrates the cost difference between replacing a CV boot versus a CV axle.  The example vehicle is a 1999 Toyota Avalon.

REPAIR: Replace Outer CV Boot Driver’s Side Axle
LABOR COST: 2.8 Hrs. X $85/hour = $238


REPAIR: Replace CV Axle Driver’s Side
LABOR COST: 1.5 Hrs. X $85/hour = $128

In this example, the cost is $5 less to replace the CV axle versus just replacing the CV boot.

CV Boot Replacement Do-it-Yourself Cost

Consider the above, the only time it makes economic sense to replace a CV boot versus the CV axle is when you do the work yourself.  CV boot kits can be purchased at your local auto parts store or online. The cost for a CV boot kit can range from a low of around $8 to as much as $40, depending on the vehicle you drive and the quality of boot kit you purchase.  A CV boot kit comes with a CV Joint Boot, CV Joint Grease Pack and Glue or Clamps.

Your content goes here. Edit or remove this text inline or in the module Content settings. You can also style every aspect of this content in the module Design settings and even apply custom CSS to this text in the module Advanced settings.

Street Smart® Technical and DIY Guides

Reflashing and ReprogrammingWhat is reflashing / reprogramming? What are your options when your vehicle needs reflashed after a new transmission is installed. Typically for 2005- Ford and GM 6-speed, 8-speed, 9-speed and 10-speed vehicles.
Automatic Transmission Repair CostsWhat is a fair price to pay for various transmission repairs? What kinds of repairs does a transmission need?
Automatic Transmission Rebuild CostsDoes your transmission need rebuilt? Fair price guide for the price range of a transmission rebuild.
Remanufactured Transmission Options and CostsConsidering a remanufactured transmission? Here are costs and options for how to purchase.
Get a Free Transmission Estimate by EmailWant an estimate for a remanufactured transmission? Fill out the form here to get an estimate via e-mail.
How to Replace a Transmission Torque Converter Clutch SolenoidWhat is a transmission torque converter clutch solenoid and how to replace one if it goes bad.
How to Replace a Transmission Pressure Control SolenoidWhat is a transmission pressure control solenoid and how to replace one if it goes bad.
How to Replace Transmission SolenoidsGuide to various automatic transmission solenoids, how they work, and DIY instructions.
How to Remove and Install an Automatic Transmission - (RWD)If you are facing a transmission replacement, you can reduce the cost considerably by removing and re-installing the transmission yourself. Here we provide step-by-step instructions for removing and replacing a transmission.
How to Replace a Transmission Speed SensorFor most vehicles, the speed sensor is plugged into the transmission (or transaxle). When the speed sensor fails the speedometer stops working and shifts may become erratic. Replacing a speed sensor is easy.
How to Release a Shifter Lever That is Stuck in ParkNothing is more frustrating than getting into your car and the gear shifter lever being locked in Park. Here we explain how to release the shifter, the causes, how to repair and the estimated cost.
How to Install an Automatic Transmission Oil CoolerInstalling an auxiliary transmission oil cooler can protect your transmission from overheating and failure. Excessive heat can ruin a perfectly good transmission very quickly. Coolers are inexpensive and easy to install.
How to Check the Condition / Level of your Automatic Transmission Fluid and Change Fluid / FilterLearn how to check the condition of transmission fluid, what the different conditions mean and what, if anything, you need to do to keep your transmission running smooth. Learn the correct procedure for checking transmission fluid level. Many people do it wrong, so here is the easy way. Keeping clean fresh fluid in your transmission is the number one thing you can do to protect the transmission from premature failure. These DIY transmission fluid and filter change procedures are easy to follow.
How to Replace a Transmission Neutral Safety SwitchThe neutral safety switch is a safety feature that prevents the engine from starting when the transmission or transaxle is in gear. When the switch fails, the engine may not crank or it may start in gear.
How to Flush Your Automatic TransmissionA transmission fluid flush can be performed without a transmission flush machine - and it's safer for high mileage vehicles.
What is Limp Mode?When a transmission fault is detected by the OBD-II system, the transmission may go into fail-safe (or "limp" mode as it is also called) in order to protect the transmission from internal damage
Transmission Diagnostic Trouble CodesDiagnostic Trouble Codes P0700 through P0799 are transmission related OBD-II codes. Any code within this range point to a transmission related fault..
How to Inspect and Repair CV Axles and CV JointsCV (constant-velocity) axles, (also known as half-shafts), are used in front-wheel drive vehicles to transfer the engine’s power from the transaxle to the two drive wheels.
Auto Repair SafetyWhen working on or around any vehicle injuries can and do occur. Please read these Safety Precautions before starting your next automotive service/repair project.